Optimization of Steam Reforming of Methane in a Hydrogen-Filtering Membrane Module with a Nickel Catalyst and a Palladium-Alloy Foil

Theoretical Foundations of Chemical Engineering - A model is proposed for steam reforming of methane in a catalytic reactor, the working section of which includes two cylindrical chambers separated...     

Effects of Solution Treatment Temperatures on Microstructure and Mechanical Properties of TIG–MIG Hybrid Arc Additive Manufactured 5356 Aluminum Alloy

A novel additive manufacturing method with TIG–MIG hybrid heat source was applied for fabricating 5356 aluminum alloy component. In this paper the microstructure evolution, mechanical properties and fracture morphologies of both as-deposited and heat-treated component were investigated, and how these were affected by different heat-treated temperature. The as-deposited microstructure showed dominant equiaxed grains with second phase, and the size of them is coarse in the bottom region, medium in the middle region and fine in the top region owing to different thermal cycling conditions. Compared with as-deposited microstructure, the size of grain becomes large and second phases gradually dissolve in the matrix as heat-treated temperature increase. Different microstructures determine the mechanical properties of component. Results show that average ultimate tensile strength enhances from 226 to 270 MPa and average microhardness increases from 64.2 to 75.3 HV0.1 but ductility decreases from 33 to 6.5% with heat-treated temperature increasing. For all components, the tensile properties are almost the same in the vertical direction (Z) and horizontal direction (Y) due to equiaxed grains, which exhibits isotropy, and the mechanisms of these are analyzed in detailed. In general, the results demonstrate that hybrid arc heat source has the potential to fabricate aluminum alloy component.     

贯筋藤凝乳剂对小鼠急性毒性与遗传毒性研究

目的探究贯筋藤作为凝乳剂的安全性。方法以贯筋藤凝乳剂为受试物,采用限量法评价贯筋藤凝乳剂对小鼠的急性毒性,观察小鼠体重及解剖后心脏、脾脏、肝脏、肾脏是否发生病变;采用Ames实验评价其遗传毒性,设20、100、500、2500、12500μg/皿剂量组进行遗传毒性实验。结果急性毒性实验未出现小鼠死亡情况。研究发现小鼠的精神亢奋,有较强攻击欲望,根据小鼠的生理状况对小鼠进行脑组织中MAO-A和5-HT含量检测发现空白组和实验组差异极显著(P0.01)。通过Ames试验检测贯筋藤凝乳剂的遗传毒性,根据结果发现在12500μg/皿的情况下出现抑制微生物生长的情况,而在2500μg/皿的剂量下统计每组菌落数差异不著性(P0.05)。结论贯筋藤凝乳剂的LD50剂量大于10000 mg/kg,并根据Ames试验确定贯筋藤凝乳剂在最高2500μg/皿不具有致突变作用。     

氮含量对HPD-1双相不锈钢组织及力学性能的影响

通过显微组织观察与力学性能测试研究了氮含量(0.08%~0.22％,质量分数)对HPD-1双相不锈钢硬度、拉伸性能、低温冲击性能及疲劳性能的影响。结果表明,氮含量变化可显著影响试验钢γ/α相比例,当氮含量由0.08％升高到0.22％,γ相含量由38.1％提高至56.5％。α相的硬度由273 HV10提高到343 HV10,γ相的硬度由238 HV10提高到299 HV10,试验钢强度明显提升。氮元素对两相比例和奥氏体相韧性的双重影响导致试验钢低温冲击性能呈先上升后下降的趋势;更高的氮含量抑制疲劳裂纹萌生与拓展,是影响HPD-1双相不锈钢室温疲劳性能的主要因素。撕裂棱是疲劳断口的显著特征。     

Early-warning performance monitoring system (EPMS) using the business information of a project

An early-warning performance monitoring system (EPMS) is proposed to objectively measure and monitor the performance of a project for early detection of inherent poor performance problems. The EPMS is built based on project progress data and consists of a database of business information, an optimized theoretical model used as a performance measurement baseline, and an index for monitoring and forecasting the performance. By monitoring the performance through an application of the EPMS to the Korean construction project, the quarterly variation of index was found to differ by project type. These results could explain the environmental changes in the project execution. Therefore, the EPMS is expected to be an alternative for objective performance monitoring and forecasting while applying the existing methods is difficult because of the limited available data on performance indicators. The development procedures may also be useful to researchers interested in approaches to quantitatively analyze trends in various industries.     

保险杠抗压分析流程自动化系统开发

为提升汽车保险杠抗压分析效率、减少重复性劳动、实现仿真分析流程的自动化，利用Python和VBS语言开发一套前、后处理自动化程序。此程序可实现RBE3单元创建、局部坐标系创建、载荷创建、头文件创建、后处理、结果诊断和报告编制等过程的自动化。实际应用结果表明，与传统人工分析相比，该程序可使仿真分析效率大幅提高。通过自动化程序进行仿真，不仅可以保证保险杠抗压分析的精度，同时还可以实现分析的标准化、保证分析的一致性。     

Deep Neural Networks for Determining the Parameters of Buildings from Single-Shot Satellite Imagery

Journal of Computer and Systems Sciences International - The height of a building is a basic characteristic needed for analytical services. It can be used to evaluate the population and functional...